TFW2005HisstankThundercatsTokuNationToyark
Go Back   Thundercats.ws > Thundercats Forums > WilyKit's Corner - Thundercats Creative > Thundercats Customs Projects

Reply
 
Thread Tools
Old 09-12-2011, 11:51 PM   #1
Lionar
Thunder Kitty
Join Date: Sep 2011
Posts: 2
Upset just as much as I am that the back of the Sword of Omens doesn't light up like the front. Problem solved. Just follow the Steps listed below and you can have it light up just like in my video below.





Things you will need:
-Phillips head screwdriver
-dremel/power drill
-Soldering iron
-Solder (Lead free)
-Bright Red LED (one of the medium sized ones 5mm I think)


1. Disassemble

===========
Take all the screws out and part the two shells/halves of the sword apart like pictured below.



Make sure to put all the screws in a safe place as well as the battery cover and batteries.


2. Innards

========
This next pic will be your best friend and save you a headache. This shows where everything goes and how it should look when you reassemble.


3. Switch and catch

==============
Next put your thumb on this switch and push it up to swing the catch out so the blade can be removed and put out of harms way.








4. Trigger

=======
Remove the trigger assembly. Set aside.




5. Led installation
=============

You will be working in the area primarily. The back of the led and the board it is mounted on.



Your LED will need a good length of wire on it to give it some wiggle room. So that it wont be stretched to the point of breaking.



Next make sure you have your wires connected properly and the positive is to positive and minus is to minus before soldering. Once you do solder your new Red LED onto the respective posts like so.





6. Drilling and mounting

=================

Grab the other halve of the sword that doesn't have the electronics.



Take a dremel or power drill and using a drill bit 1/8 th size and drill a hole in the center most area of this piece. Be careful not the drill out and right through the eye. Also use the drill to widen the hole a bit as well to fit the new led.



This next part call for being somewhat fast with your hands. Super glue around the hole you just drilled. And set the led inside the newly made hole.





7. Reassemble
===========

Once the glue has dried put everything back together(use innards pic above if stuck on where things go back to) and if done right everything should work as it normally does. Expect both sides now light up.


Attached Thumbnails
Click image for larger version

Name:	gloweye2.JPG
Views:	1
Size:	14.7 KB
ID:	694Click image for larger version

Name:	diassembled.JPG
Views:	153
Size:	169.6 KB
ID:	695Click image for larger version

Name:	innards.JPG
Views:	152
Size:	130.2 KB
ID:	696Click image for larger version

Name:	switchcatch.JPG
Views:	148
Size:	67.3 KB
ID:	697Click image for larger version

Name:	switchflip.JPG
Views:	150
Size:	53.0 KB
ID:	698

Click image for larger version

Name:	removeblade.JPG
Views:	151
Size:	77.1 KB
ID:	699Click image for larger version

Name:	trigger.JPG
Views:	149
Size:	67.7 KB
ID:	700Click image for larger version

Name:	LEDboard.JPG
Views:	146
Size:	73.0 KB
ID:	701Click image for larger version

Name:	LED.JPG
Views:	146
Size:	102.1 KB
ID:	702Click image for larger version

Name:	solderprong.JPG
Views:	144
Size:	85.0 KB
ID:	703

Click image for larger version

Name:	LEDmount.JPG
Views:	144
Size:	116.8 KB
ID:	704Click image for larger version

Name:	drillspot.JPG
Views:	143
Size:	72.5 KB
ID:	705Click image for larger version

Name:	drillhole.JPG
Views:	143
Size:	78.6 KB
ID:	706Click image for larger version

Name:	glue.JPG
Views:	143
Size:	30.2 KB
ID:	707Click image for larger version

Name:	length.JPG
Views:	144
Size:	74.1 KB
ID:	708

Click image for larger version

Name:	gloweye.JPG
Views:	145
Size:	40.6 KB
ID:	709

Last edited by Lionar; 09-13-2011 at 12:22 AM..
Lionar is offline   Reply With Quote
Old 09-13-2011, 07:55 AM   #2
Cat's Pajamas
Thunderian Commoner
Cat's Pajamas's Avatar
Join Date: Feb 2011
Posts: 210
Great tutorial, thanks!
Cat's Pajamas is offline   Reply With Quote
Old 09-13-2011, 10:24 AM   #3
IndyCat
Thunderian Commoner
Join Date: Aug 2011
Location: Indianapolis, IN
Posts: 490
awesome thanks for the tut! Now we just need to make the blade spring loaded!!!! Then it would be flippin amazing!
IndyCat is offline   Reply With Quote
Old 09-13-2011, 10:53 AM   #4
Lionar
Thunder Kitty
Join Date: Sep 2011
Posts: 2
Quote:
Originally Posted by IndyCat View Post
awesome thanks for the tut! Now we just need to make the blade spring loaded!!!! Then it would be flippin amazing!
Actually It might not be that hard to do. I will look into this tonight and post results.
Lionar is offline   Reply With Quote
Old 09-15-2011, 07:33 AM   #5
Lion O of savannah
TruthJusticeHonorLoyalty
Join Date: Aug 2011
Location: savannah ga
Posts: 44
BADA$$ LIONAR, well done
Lion O of savannah is offline   Reply With Quote
Old 09-28-2011, 04:41 PM   #6
Scelestus Unus
Thunder Kitty
Join Date: Sep 2011
Posts: 22
One thing I noticed that Lionar didn't mention is that if you take out the electrics board you will find a light restricting dome that looks like a clear white dome with a pinhole in the middle. It easily pops out and allows the Thundercats symbol to light up slightly brighter.

I'm amazed because I did almost the exact same mod as you before seeing this thread. I was going to unscrew the eyes and place magnets on the back of them so I could switch out the eyes on either side, but it wasn't very practicle.

I decided to add a light to the back, but since I can't solder I took the led from a bubble machine fish keychain, ran it to the cats eye, and drilled a hole for the new button on the hilt of the sword. So while I have to push another button to get it to work, my cats eye lights up as well.
Scelestus Unus is offline   Reply With Quote
Old 10-30-2011, 09:34 PM   #7
BWDinobot
Thunder Kitty
Join Date: Sep 2011
Posts: 9
awesome. Now I need to go get that sword. Thanks for a great tutorial on how to do this.
BWDinobot is offline   Reply With Quote
Old 10-31-2011, 03:27 PM   #8
englishw
Thunderian Commoner
Join Date: Aug 2011
Location: Salem, Oregon
Posts: 299
Amazing! I'm going to have to try it myself! Thanks!
englishw is offline   Reply With Quote
Old 11-07-2011, 04:21 PM   #9
shmashwitdaclub
Thunder Kitty
Join Date: Aug 2011
Posts: 30
very cool!
shmashwitdaclub is offline   Reply With Quote
Old 11-07-2011, 06:10 PM   #10
Dedboy
Thunder Kitty
Join Date: Jul 2011
Location: The Fright Zone
Posts: 55
Very nice job! Well done!!! :]
Dedboy is offline   Reply With Quote
Reply

Thread Tools

 
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sword of Omens : Would you pay this much? IndyCat Thundercats on eBay 7 09-04-2011 12:50 PM
Anyone have the old Sword Of Omens? Ruination04 Thundercats Toys and Merchandise 16 08-27-2011 07:04 PM
Classic Sword of Omens 77kustoms Thundercats Toys and Merchandise 1 08-20-2011 09:33 AM
Thundercats 2011 Deluxe Sword of Omens & Basic Claw Shield SEANxLONG Thundercats Reviews and Feedback 4 08-04-2011 07:50 AM
SDCC Replica Sword of Omens and FREE Foam Sword of Omens RoftheHood Thundercats News and Rumors 16 07-24-2011 05:07 PM

 

All times are GMT -5. The time now is 10:56 AM.

Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by vBadvanced CMPS